久久综合丁香激情久久-久久综合电影-久久笫一福利免费导航-久久资源365-在线亚洲中文精品第1页-在线亚洲视频无码天堂

WELCOME TO THE OFFICIAL WEBSITE OF ENGLISH | 簡體中文

> News

Blowing machine use precautions!

Time:2019-4-2 17:13:48
Strictly observe the precautions for the use of the film blowing machine, which can reduce the mechanical loss and prolong the service life of the machine. If you encounter other problems during use, please contact us!
 
1. Due to possible damage to electrical components or wire heads during transportation, strict inspection should be carried out first. In order to ensure personal safety, the opening mechanism must be connected to the ground wire, then the power supply is turned on, and then the motor operation of each part is strictly checked, and attention is paid. There is no leakage.
2. When installing, pay attention to adjust the center line of the extruder head and the center of the traction roller to be horizontal and vertical, and must not deviate from the skew.
3. When the winding is increased, the outer diameter of the winding is gradually increased. Please pay attention to the matching between the pulling speed and the winding speed. Please adjust it in time.
4. After the host is turned on, pay close attention to the operation of the host, adjust, correct, and adjust the electrical instrument and controller in time to ensure its normal operation.
5. The main gear box and traction reducer should be refueled frequently, and the gear oil should be replaced. Please replace the new gear oil with the new machine for about 10 days to ensure the normal operation of each rotating part. Pay attention to refueling to prevent jamming and overheating damage. Check the tightness of each joint to prevent the bolt from loosening.
6. The compressed air in the bubble tube should be kept in an appropriate amount. Because the compressed air leaks out during the traction process, please replenish it in time.
7, often clean and replace the filter inside the machine head to prevent blockage, to prevent plastic particles mixed into the iron, sand, stone and other impurities to avoid damage to the screw barrel.
8. It is strictly forbidden to turn the material without turning the material. When the barrel, tee and die have not reached the required temperature, the host cannot be started.
9. When starting the main motor, start the motor and accelerate slowly; when the main motor is turned off, it should be decelerated before shutting down.
10, when preheating, heating should not be too long and too high, so as to avoid blockage of the material. The blown film machine frequency conversion speed control dragging system consists of two parts: one is the frequency converter that squeezes the main motor, and the other is the frequency converter of the traction motor. Their control is very simple, the speed of the motor can pass the keyboard of the panel. Or externally set the potentiometer to adjust. The design of the mold (die) is also related to the quality of the blown film, the smoothness of the spiral body and the inner wall surface of the cavity, the absolute balance of the spiral (the absolute balance of each splitter), the pressure inside the cavity, and the die. Extension angle, depth (height) of the die setting section, ratio of die gap and blown film thickness, total height of the die, wall thickness of the die barrel (insulation), design of the outer heating ring (heating temperature uniformity) Distribution, etc., are the key points to be carefully designed to blow "perfect" films. Ascending and decelerating time: Since plastic machinery does not need to be frequently started and braked, there is no strict requirement for the speed of lifting. The film blowing machine is based on the principle that the rated current is not exceeded, but the sealing and cutting machine should be preset as short as possible.
Prev:Blown film machine energy-saving intelligent, power plastic!
Next:Analysis of blown film related processes and common problems!


Home   -  About Us   -  Products   -  News   -  Video   -  Message   -  Contact
Copyright © 2025 All Rights Reserved.      Technical support:Lianke

Please Scan
QR code

Message

weekday:7:30-17:00
weekend:7:30-17:00

Open

Please leave a message
*

Title

*

Name

*

Tel

*

E-mail

*
主站蜘蛛池模板: 中文字幕乱码一区AV久久 | 艳鉧动漫1~6全集观看在线 | 熟女人妻久久精品AV天堂 | 小雪奶水涨翁工帮吸的推荐语录 | 翁公与小莹在客厅激情 | 精品无码三级在线观看视频 | 末成年美女黄网站色大片连接 | 亚洲人成网站在线观看90影院 | 老司机深夜福利ae 入口网站 | 成人精品视频在线观看播放 | 日本后进式猛烈xx00动态图 | 成人在线小视频 | videos gratis欧美另类 | 九九久久国产 | 99热精品在线av播放 | 国产一区在线观看免费 | 成人公开免费视频 | 亚洲va久久久久 | 最新亚洲人成网站在线影院 | 久久久精品免费视频 | 亚洲精品国产自在现线最新 | 国产亚洲一区在线 | 宫交拔不出来了h黑人 | 亚洲精品久久久午夜福利电影网 | 在线自拍亚洲视频欧美 | 老版香蕉版下载 | 2021久久99国产熟女人妻 | 亚洲精品久久久久AV无码林星阑 | 亚洲中文久久精品AV无码 | 考试考90就可以晚上和老师C | 亚洲AV无码国产精品色午夜情 | 国产精品高清视亚洲一区二区 | 18禁三级黄 | 亚洲永久在线观看 | 耻辱の奴隷淑女中文字幕 | 一久久 | 最新无码国产在线视频2020 | 亚久久伊人精品青青草原2020 | 国产午夜精品AV一区二区麻豆 | 亚洲AV国产国产久青草 | 免费看国产曰批40分钟 |